Skip to content
Berger-Seidle AquaSeal ExoBloc 5L white plastic jerry can with a blue AquaSeal panel and a timber graphic, white background

Spotted gum vs blackbutt: how each looks, wears and takes a finish

Ready to buy? EcoGrit stocks the products in this guide and ships Australia-wide. Shop the sealers and primers range.

You have narrowed your floor or deck down to spotted gum or blackbutt. Both are hard, termite-resistant hardwoods from Australia's east coast. What separates them is colour, how hard they are to dent, and how each one behaves under a sealer, lacquer or oil.

This guide compares spotted gum vs blackbutt on published species data, then works through the finishing choices for each. For more on each species, see our spotted gum flooring guide and blackbutt flooring guide.

Spotted gum vs blackbutt at a glance

Property Spotted gum Blackbutt
Botanical name Corymbia maculata, C. citriodora and C. henryi Eucalyptus pilularis
Heartwood colour Light brown to dark red-brown Golden yellow to pale brown, occasionally slightly pink
Texture and grain Moderately coarse and uneven; wavy grain can give a fiddleback figure Even texture; grain generally straight, sometimes interlocked
Density, seasoned 990 kg/m³ 900 kg/m³
Janka hardness, seasoned 10.1 kN 8.9 kN
Natural durability Class 1 above ground, Class 2 in-ground Class 1 above ground, Class 2 in-ground
Tannin and extractives Minimal staining; less prone to tannin bleed-through than other Australian hardwoods High extractives in mature wood

Botanical names and durability classes are from Business Queensland; the rest is from WoodSolutions. Figures vary between sources, so use them to compare, not as exact values.

How they look

Blackbutt is the paler, more even timber: golden yellow to pale brown heartwood, an even texture and mostly straight grain. Spotted gum runs from light brown to dark red-brown, with a coarser texture and, where the grain is wavy, a fiddleback figure. Its sapwood is usually white to light brown and can be up to 50 mm wide.

Both can show gum veins. Business Queensland says they are common in spotted gum, and WoodSolutions notes small gum veins may be visible in blackbutt.

Before you commit, take offcuts of your actual boards, palest and darkest included, through the full system you plan to use.

How they wear: hardness and durability

Spotted gum is the harder of the two, at 10.1 kN Janka hardness seasoned against 8.9 kN for blackbutt. Business Queensland rates spotted gum very hard to indent (1 on its 6-class scale) and blackbutt hard (2 on the same scale). Harder timber resists denting better, but neither species is dent-proof.

Outdoors, Business Queensland rates both Class 1 for above-ground durability and Class 2 in-ground, and both are rated termite resistant.

Tannin and extractives: how they differ

WoodSolutions describes spotted gum as a minimal staining timber, less prone to tannin bleed-through than other Australian hardwoods.

Blackbutt is different. WoodSolutions says the high extractives of mature blackbutt can cause problems with some adhesives, though much less so in young regrowth wood, and can stain painted surfaces exposed to the weather. Its tendency to surface check can also cause issues with painting.

We go deeper on each species in finishing blackbutt and stopping tannin bleed and finishing a spotted gum floor.

Which sealer suits each species

In the AquaSeal system, the first coat on bare timber is a sealer: one coat only, never cut back. Your choice of sealer also changes the look.

Sealer Effect on the look Our product guidance lists it for
AquaSeal ExoBloc Intensifies the wood colour Tannin-rich timber
UniQuick Primer Enhances colour and grain Tannin-rich timber
AquaSeal FlexPrimer Neutral colour, medium grain enhancement Most common timbers, such as oak and pine

Roll ExoBloc on evenly and generously with a 10 mm microfibre roller, at about 10 m² per litre. Berger-Seidle says it can be overcoated after 1 to 2 hours under normal conditions, but recommends only one roller coat per day so the wood can release absorbed moisture. UniQuick, an alcohol-based sealer, goes on with a 5 mm mohair roller or a Universal Roller.

Blackbutt. WoodSolutions flags the high extractives of mature wood, so treat it as tannin-rich and use ExoBloc or UniQuick. Both enhance colour, so expect blackbutt to finish less pale than the raw board. If staying pale matters most, make test boards first, and see our guide to white and whitewashed timber floors.

Spotted gum. WoodSolutions calls it a minimal staining timber: less prone to bleed-through, not free of it. ExoBloc or UniQuick will enhance its colour. If you want a neutral look instead, test on offcuts and call our technical team before you swap to FlexPrimer.

Topcoats over the sealer

Two coats of a 2-pack topcoat go over the sealer, a three-coat system overall. Berger-Seidle lists CeramicStar and GreenStar as topcoats for ExoBloc, and names ExoBloc and UniQuickPrimer among the primers for CeramicStar.

  • AquaSeal CeramicStar. A 2-component, water-based polyurethane with ceramic components, which Berger-Seidle describes as highly abrasion resistant. Usable after 12 hours; no rugs, carpets or care products for 7 days.
  • AquaSeal GreenStar. A 2-pack with hardener: 18-hour pot life and 48-hour cure. Our product guidance lists it as green and sports floor certified.

Oiling a spotted gum or blackbutt floor

Rubio Monocoat Australia's Oil Plus 2C tip sheet names no species, so the same rules apply to both. Sand to 120 grit maximum, because a finer grit means less oil goes in and so less protection. After vacuuming, remove the remaining dust with Rubio Raw Wood Cleaner and let it dry fully, or use a tack cloth.

The step that depends on the timber is WoodPrep. On very dense timbers, the tip sheet uses it instead of Raw Wood Cleaner to open the grain, left to dry fully before oiling. It does not define very dense, and both species are dense, at 990 and 900 kg/m³ seasoned, so ask our technical team whether your boards need it. WoodPrep also increases colour intensity under a pigmented Oil Plus 2C, so test it on an offcut first. Our blackbutt post above sets out the application steps.

Spotted gum vs blackbutt decking

WoodSolutions lists decking among the uses for both species. For DuroGrit, Rubio Monocoat Australia names a natural-look colour for each: Foxy Brown for spotted gum and Grassland Beige for blackbutt. DuroGrit's warranty applies only to durability class 1 and 2 timber, among other conditions, and both species qualify.

Our decking oil vs deck stain guide explains how to match a DuroGrit colour to your timber, and our step-by-step decking oil guide covers sanding and application. Two more points from Rubio's data sheet:

  • The water test. Once the prepared boards are dry, sprinkle on a few drops of water. If they don't soak in within a few seconds, the wood is not dry or porous enough, so don't apply.
  • Weathering new boards. The data sheet asks for (tropical) hardwoods, such as afzelia, iroko and cumaru, to weather outdoors for about 4 to 6 weeks before preparation, because their natural extractives or oils can impede penetration or drying. It does not name spotted gum or blackbutt, so ask our technical team before you coat new boards.

WOCA Exterior Wood Oil is another option: a water-based oil that WOCA says enhances the natural colour and grain of the wood. WOCA's preparation is to clean with Exterior Wood Cleaner and let the wood dry for at least 24 hours. Test tints from the 25 ml sample pack on your own boards.

Spotted gum or blackbutt: which suits your job?

If you want Lean towards Finishing note
A pale, even floor Blackbutt ExoBloc or UniQuick will enhance its colour, so make test boards
Brown to red-brown tones, sometimes with figure Spotted gum ExoBloc or UniQuick will enhance its colour; test on offcuts
More resistance to dents Spotted gum 10.1 kN Janka against 8.9 kN
A natural-look oiled deck Either DuroGrit Foxy Brown on spotted gum, Grassland Beige on blackbutt

Not sure which system suits your spotted gum or blackbutt? Call our sales team on 0403 964 703, or technical support on 0401 270 818 for application advice.

Sources


Products in this guide

All available from EcoGrit, shipped Australia-wide. Trade pricing available for flooring professionals.

Timber Flooring Specialist

Bill Lazzio is a timber flooring specialist with over 30 years of hands-on experience in floor sanding, coating, and restoration across residential and commercial projects in Australia. Bill works with EcoGrit and leading European manufacturers to bring professional-grade, low-VOC products tailored to Australian conditions.

Next article Whitewash floorboards: lye and white oil, white stain or white lacquer